Peel-and-Stick Planks of Reclaimed Wood Make Striking Wall Décor

timberchic wall planks

By Matt Weber

Accent Wall by Timberchic

As part of an ongoing remodeling project, the EHT staff had our first opportunity to install Timberchic, a peel-and-stick plank made of genuine reclaimed wood. Thin, lightweight, and easy to cut and apply, these DIY-friendly planks are made 100-percent from reclaimed river logs and are available in a range of board widths and wood tones (we chose Coastal White). They’re ideal for creating accent walls but can also be used on ceilings, backsplashes, doors, columns and more. We used them to accent the surrounding foyer walls of a home’s front entry.

The smooth, wipe-able surface exhibits all the distinct characteristics of real wood, but requires no glue, nails or screws to install. To apply the planks, you simply peel the backing off the adhesive strips, butt the edges to the adjoining planks, press into place and secure with a roller.

Tools Required:

  • Pencil
  • Chalk Line
  • Level
  • Rubber J-Roller
  • Miter saw (either hand saw or electric)
  • Jigsaw
  • Utility Knife
  • Black Dot Stickers (provided)

Ordering & Preparation

To order the Timberchic product, you’ll need to calculate the amount of square footage of your project, then add 5 percent to account for waste. Also, determine whether you need any outside corners or end caps—or if you’ll be customizing any of the surrounding trimwork using a different material.

The wall surface needs to be clean (free and debris and loose drywall), smooth (so sand down any bumps) and flat (within 1/4 inch over 4 feet). Any wall repairs requiring joint compound need to be primed or painted.

Remove any fixtures attached to the wall (outlet covers, switch covers, wall sconces, etc.). Also, remove any existing trim that will interfere with installation.

Layout

Aside from the peel-and-stick simplicity of applying the boards to the wall, the installation procedure is similar to laying a board-pattern floor. This means you need to establish a level and square layout pattern. We ran a 4-foot level along the ceiling and floor of our work area, and were lucky enough to find that our wall and ceiling were level.

Each Timberchic plank is made of genuine reclaimed wood, only about 1/8-in. thick to conform to the wall.

However, builders make mistakes and houses settle, so not every situation will be so neatly square. If you find the floor and ceiling aren’t level, measure the distance between your floor and ceiling at both ends of the wall. If these are within 1/4 inch, then your floor and ceiling are adequately parallel.

If you determine that your ceiling is fairly level, you can use your ceiling as the reference point for laying out your starting row. Base molding can be used along the floor to disguise an out-of-square gap along the bottom row.

 

If both the ceiling and floor are out of level, you can begin a level starting row in the middle of the wall, then work upward and downward until your rows reach the floor and

Simply peel off the tape packing to reveal a very strong adhesive.

ceiling, where you can conceal those out-of-square gaps with trim. However, if you take this approach, first measure from the anticipated height of your center row to both the ceiling and the floor. Divide these measurements by the width of your Timberchic planks. If you end up with a small remainder (i.e. a very thin “sliver” board) at the top or bottom, then adjust the height of your starting row to ensure a larger final row at the top and bottom. For example, a 1-in. row is too narrow and not optimal for finishing a room. Ideally, you want to have a row no less than 1/2 the width of a normal row.

Installation

I realize that some people cringe at the thought of a “peel-and-stick” product because inferior products in the past have been known to come “unstuck” and move around (I’m looking at you, cheapo peel-and-stick flooring). Take my word from experience that the Timberchich strips utilize a very strong adhesive, and once a board is pressed firmly to a wall, you’re more likely to tear the wood plank off the strips than you are to pull the strips off the wall. We’re talking about a very strong glue. For this reason, all measuring, cutting and test fitting of planks must be done prior to removing the tape film. After the tape film has been removed, avoid touching the adhesive strips and protect them from dust and debris.

Here’s the “before” shot of our foyer project, showing the walls are nothing special.
All remodeling jobs are different so plan the project in advance. This one required a telescoping ladder to access the tall walls above a staircase.
The best case scenario is that your ceiling and floor are level and parallel.

If any of the planks have an open knot, simply use the “black dot stickers” (included with each box of planks) behind the knot to hide the wall. To do this, place the plank in its desired location before removing tape liner. Mark any open knots on the wall with a pencil. Remove the plank and place a black dot sticker over the pencil mark.

The ceiling and floor are parallel within 1/4″ (and the ceiling is fairly level), you can use the ceiling as a reference point to start the first row.
Unscrew any switch plates or outlet covers, and tape the screws to the plates for replacement.

To place a plank in its final position, remove the tape liner, align the plank along the reference line or adjacent plank with a slight angle so only the edge is touching. Make any necessary adjustments and lightly press the plank into place.

Begin the first row in a corner.
Pressure from a rubber J-roller strengthens the bond of the adhesive.
Carefully mark the face of the planks for cutting.

Double-check the fit before applying pressure to the plank with a rubber J-roller. The pressure-sensitive adhesive achieves a better bond the more pressure that you apply. Pay extra attention to pressing down the edges and ends of the plank.

A miter saw is handy tool for making quick cuts in the planks.
The thin blade of a jigsaw is easy to maneuver when making notches or inticate cuts.

The planks are designed to simply butt against each other at the joints. Similar to floor-board application, the butt joints in adjacent rows should be staggered the width of the plank, at a minimum.

Each box of Timberchic includes “black dot stickers” to fill any knotholes in the wood.
When removing trimwork, pry it off carefully and pull out the nails if you have any intention of reusing the material.

A miter saw makes the best tool for cutting the planks to size.

Stagger the end joints between rows by the width of a plank (at minimum).
Small areas like the side of this door are a great place to use cut-off end pieces.

Also, keep a jigsaw handy to cut notches around light switches or any other odd shapes or angles.

Take the opportunity to make any repairs or improvements you come across. We applied spray foam insulation around this door jamb.
We finished the walls around the door and floor with custom trimwork.

Once the field is completely finished, finish up with the trim package of your choice. On this job, we went with a simple picture-frame door surround and matching baseboard package, which we felt complemented the rustic “driftwood” look of the new accent wall without distracting from it with ornate trimwork. In the end, we felt the new Timberchic wall planks added a great deal of character to what was otherwise a fairly uninteresting living space. Mission accomplished.

Learn more about these adhesive wood wall planks at www.timberchic.com.

Side Note

Template Trick

If you find careful measurement to be a challenge, you can easily make a paper  template to copy odd shapes, and then transfer them to your planks. Simply crease the papers edges to match the shape in question, then align the paper template over the board and trace the cutline.

Hot Product

fence trac
FenceTrac Fence Systems

FenceTrac is a revolutionary fence system that uses patented U-channel rails and metal posts to create a secure and sturdy frame for any type of infill. You can choose from wood, vinyl, composite, bamboo, metal, or any other material that fits your style and budget. You can also mix and match different infills to create […]

Read More >>