More from EHT:

Upgrading a Utility Trailer

Upgrading a stripped-down utility trailer to move mulch and tow your tools.

By Mark Clement

I’m a trailer guy. Yes, a dump truck would rock for heavy haul-outs, and a big box truck would be great for storing tools and serving as a mobile workshop. But, depending on the day, the work we do may range from residential bathroom improvements to our Food Network bakery make-overs. We may also tackle a weekend DIY project like hauling mulch and a mower to a friend’s house. This variety of jobs requires the flexibility a trailer offers.

We can also leave a trailer at the jobsite and just drive the truck by itself, which isn’t possible with the aforementioned vehicles. Part FedEx, part dumpster, all workhorse, our trailer sees no end to its work … or play, for that matter. A utility trailer is a king vacation machine, too. Forget about jamming everything you own into the SUV. Put the bikes, beach blankets and Beanie Babies in the trailer and ride in style.

If all you have is the common 16-in. tall angle-iron trailer body, you’re limited to how much you can get in and out of a simple utility trailer. That is, unless you add to it.

A basic “no walls” utility trailer is a platform. Sure, it can carry some stuff, but will get left in the dust by a trailer tricked out to roll with all your building equipment.
A basic “no walls” utility trailer is a platform. Sure, it can carry some stuff, but will get left in the dust by a trailer tricked out to roll with all your building equipment.

Tools and Materials

Obviously, you’ll need a trailer. Mine is a 5-by-10-ft. two-wheel utility trailer. Nothing fancy, yet.

The upgrade shown in this article requires 2x material for the posts and materials racks, 1/2-by-3-in. galvanized through bolts, 3-in. deck screws, and 1x or 2x material for the walls. You’ll also need a drill and bits to drill out steel and a saw to cut stuff.

The Build

First, cut the posts or staves. My trailer walls are about 40-1/2 inches tall. It’s a great height for everything I carry. I fill in the trailer framer around the wheel wells, then stack four 2x8s for the walls. I’ve made the staves from 2×4 in the past, but I beefed them up in this build to 2×6 pressure treated pine because I knew I’d be lashing loads to the top of them. (More on that later.) Also, install the vertical staves ‘wild’ and cut them to final length later.

Cut the staves to support the wall. A 2x4 will work, but I beefed them up to 2x6 because I knew I’d be lashing loads to the top. Also, if you move a lot of debris or mulch then beveling the edges of the stave makes the trailer easier to clean out.
Cut the staves to support the wall. A 2×4 will work, but I beefed them up to 2×6 because I knew I’d be lashing loads to the top. Also, if you move a lot of debris or mulch then beveling the edges of the stave makes the trailer easier to clean out.

You’ll need to drill bolt holes through the trailer frame to mount the staves. Here’s a tip for drilling steel that makes the job easier. First, locate the hole. Next drill a pilot hole with a small (1/8-inch), very sharp bit that is designed to drill steel. Once the pilot hole is drilled, follow up with the right diameter bit, in this case 5/8-in. to accommodate a 1/2-in. bolt.

When drilling metal, drill a small pilot hole with a very sharp bit.
When drilling metal, drill a small pilot hole with a very sharp bit.

Use a drill to drill the holes, not an impact driver. Steel likes to be drilled more slowly than wood, so an impact driver might not perform well. Some people drip oil on the bit to keep it lubricated and cutting well.

The pilot hole makes drilling the full-diameter hole much easier.
The pilot hole makes drilling the full-diameter hole much easier.

Once the holes are drilled, square up the staves to the trailer body, then hold them fast with a couple of bar clamps. Drill through the steel and through the wood. Pop in the through-bolts and hand-tighten the nuts before socking them tight with a socket set or impact wrench.

Clamp the stave square to the trailer frame and drill the hole for the through-bolt.
Clamp the stave square to the trailer frame and drill the hole for the through-bolt.

I center all but the end and corner staves on the trailer’s steel posts to make fastening the planking to the staves easier later on. It also gives the through-bolts the maximum meat to hold onto for heavy loads.

Square the staves to the trailer and insert the through-bolts. Use cut washers on both sides and tighten with a socket or impact driver. Tighten until the washer crunches into the wood fiber. If you’re using new treated wood with high moisture content, check the connections again in a week and re-tighten as necessary.
Square the staves to the trailer and insert the through-bolts. Use cut washers on both sides and tighten with a socket or impact driver. Tighten until the washer crunches into the wood fiber. If you’re using new treated wood with high moisture content, check the connections again in a week and re-tighten as necessary.

Next, install the planking. To make life easier I span the trailer’s wheel well with blocking on the inside of the trailer, installing the boards flush with the staves. To make the butt-joint connections between the boards set edge-to-edge, I make what I call “no-jig pocket holes”. I drill angled pilot holes large enough and deep enough to countersink the screws. This makes driving toe-screws much easier than any other method I’ve tried. For the oddball angles by the wheel well, I used the Starrett ProSite Protractor—love that thing—to lay out the angles.

I span the trailer’s wheel well with blocking on the inside of the trailer, installing the boards flush with the staves.
I span the trailer’s wheel well with blocking on the inside of the trailer, installing the boards flush with the staves.

Next, I start at the back and work my way around, piecing in all the small pieces and ripped blocking to create a solid wall on the trailer frame. It gives me peace of mind hauling, well, everything.

Add blocking as needed to create a wall around the trailer’s angle iron projections.
Add blocking as needed to create a wall around the trailer’s angle iron projections.

I used 2x pressure-treated pine for the planking on this trailer upgrade, and it is virtually bomb-proof. But 2x is heavy making the trailer hard to move around by hand. If I had a tractor or ATV, that wouldn’t be a big deal, but I don’t. Another option would be to use 1×12 #2 pine. I formerly had a trailer built with 1×12 and not only was it much lighter; it lasted for nearly a decade of professional use. Bottom line: your call.

For mapping out the weird wheel well angles I used one of my fave tools: the Starrett ProSite Protractor.
For mapping out the weird wheel well angles I used one of my fave tools: the Starrett ProSite Protractor.

To get the first course of planking started on my trailer where there are interruptions from the wheel wells and corners, I used a couple of bar clamps to hold the pieces where I wanted them before bombing in the screws.

Get the first course of planking started. To hold the pieces tight if you’re working alone, a few bar clamps can be your best friend. Lock ‘em and sock ‘em. To get a really cool, powerhouse look, I alternated the corners to create a kind of box joint.
Get the first course of planking started. To hold the pieces tight if you’re working alone, a few bar clamps can be your best friend. Lock ‘em and sock ‘em. To get a really cool, powerhouse look, I alternated the corners to create a kind of box joint.

To make the look interesting, I like to alternate the corners. I think it makes the corner stronger but I also really like the box-joint, custom look.

Once you’ve planked up the sides, cut all the staves to length except the front and back, which will be vertical supports for the materials racks.
Once you’ve planked up the sides, cut all the staves to length except the front and back, which will be vertical supports for the materials racks.

Every now and again a 3-in. deck screw tip makes it through the laminated 2-bys (which is 3 inches thick). It’s hardly a hazard unless you’re just crushing the heads into the wood and the points are really showing, but I blunt them with a hammer whack anyway. I’ve been cut, scraped and scratched by everything else. What would make these screw tips any different?

Blunt any screw tips that make it through the laminated 2-bys.
Blunt any screw tips that make it through the laminated 2-bys.

Material Handlers

While the hero function of most trailers, including mine, is to hold stuff inside the walls, there’s no reason you can’t rack ‘em up to carry the long stuff like ladders, lumber or molding.

Make and install the materials handlers, aka ‘racks’.
Make and install the materials handlers, aka ‘racks’.

The material rack on my trailer is fixed to the staves (which I didn’t cut flush with the trailer walls) but kept at 53-inches above the trailer deck so it would clear the trailer’s tailgate. It’s a T-bracket of 2×8 that bridges the staves.

The end of the rack is also a T, but I fabricated a pocket for it to sit in so the

T is removable. The reason for this is that a horizontal rack gets in the way when hauling tools, mulch, or plaster debris. In other words, if I made it a fixed-feature I’d literally have to duck under it every time I walked into the trailer with a sheet of drywall.

Marine cleats are the world’s best tie-down anchor. I have 3 on each side of the trailer with 3/8” nylon braided line as my tie-down material. To make the rear cross-piece removable, I fashioned a slotted pocket out of scrap 2x6 that holds the leg of the T-shaped rack.
Marine cleats are the world’s best tie-down anchor. I have 3 on each side of the trailer with 3/8” nylon braided line as my tie-down material. To make the rear cross-piece removable, I fashioned a slotted pocket out of scrap 2×6 that holds the leg of the T-shaped rack.

So whether I’m hauling for work or hauling out of town for vacation (who am I kidding—vacation?), my stuff is safe and secure for the long haul.

Editor’s Note: Mark Clement is co-host of the MyFixitUpLife show, General Contractor on Food Network’s Save My Bakery and spokesman for Wood Naturally.

Side Note

Extra Features

As much use as I get out of this trailer trick-out, I added some details (and would like to add more) that max it out even further.

trailer extrasTool Holder. I added a triangular front piece on the trailer tongue to hold shovels and other long-handled tools. The triangular shape makes this wall of the trailer a little more aerodynamic for easier towing.

Cleats. I added six cleats like you’d find on a dock or ski boat as anchor points for quickly cinching and un-cinching loads using rope. From tarps to lumber, these are essential (and cheap) additions for me. I use bowline knots and trucker’s hitches to secure the material.

Truck Box. I also added a few blocks inside the trailer walls to set my old truck box on. When I roll to a jobsite, I can store any number of tools in there. For vacation, it’s awesome for anything from beach toys to beer and ice or grocery store stuff you want to bring.

Hot Product

fence trac
FenceTrac Fence Systems

FenceTrac is a revolutionary fence system that uses patented U-channel rails and metal posts to create a secure and sturdy frame for any type of infill. You can choose from wood, vinyl, composite, bamboo, metal, or any other material that fits your style and budget. You can also mix and match different infills to create […]

Read More >>