More from EHT:

Grouting & Sealing Non-Glazed Bathroom & Kitchen Tiles

Tile sealing

Keep it Clean Longer

By Rob Robillard

I’m a remodeling contractor in the Northeast and can tell you that most bathroom remodelers do not take the time to seal tile grout for their customers.

I could speculate why, and I’d probably point to a missing level of professionalism, ignorance, communication and cost—but that’s for a different article. This article will focus on the proper techniques for sealing tile and grout.

Why Seal it?

The primary reason for sealing non-glazed tile and grout (especially grout) is to keep it looking fresh and clean. Non-sealed tile and grout gets grimy and stained over time, requiring a lot of scrubbing and sometimes even replacement to look good again.

Sealing tile and grout provides water and oil-based stain resistance and delays grout discoloration. Sealed tiles and grout are much easier to clean and stay clean longer.

Not all tile and grout require sealing. Glazed tiles are coated with a liquid glass, which is baked into the surface of the tile by the manufacturer. The glaze fills in the tile’s microscopic imperfections, protects from stains and creates an extremely durable surface.

You should only seal cement-based grout, which is extremely porous and can harbor dirt, mold, mildew and bacteria. However, epoxy, urethane and other types of synthetic grouts do not need to be sealed.

All unglazed tile and any cement-based grout should be protected with a penetrating sealer. Much like the porous grout, unglazed tile has microscopic imperfections that will, over time, accumulate gunk and cause your floor to always look dirty.

Sealing the tile and grout is not a one-time event. Unfortunately, the sealant is a maintenance issue and needs to be reapplied every two years, and sometimes sooner.

The best time to apply the first coat of sealer is 72 hours after the grout is installed.

If you or your contractor did not seal your tile when it was installed, it is never too late.  The tile and especially the grout will need to be thoroughly cleaned, because applying sealer will lock in any stains or discoloration. In most situations, cleaning grout can be accomplished by using a stiff bristle brush and simple dish soap. Badly stained grout may require a stronger cleaner or even grout replacement.

Simple Steps to Apply Sealer

Cleaning Tile and Grout

1.  Clean tile and grout thoroughly.

2.  Ensure tile and grout are completely dry.

Materials need for sealing Tile and Grout

3.  Mask off any areas you do not want to get sealer on.

Applying Sealer

4. Liberally apply a quality fluorochemical-based sealer to unglazed tile and non-epoxy grout. Applying with a foam brush can eliminate bristle marks, and the narrow tip can access grout lines.

Apply Sealer to grout lines

5.  Allow the sealer to penetrate for the duration of time recommended by the manufacturer, and then apply a second coat. If sealer has dried on the tile and streaking is present, use a “sealer dampened” towel to remove and then a dry towel to wipe clean.

Wipe away excess sealant

6.  Wipe off excess sealer with a clean, dry towel.

7.  Follow the manufacturer’s directions for drying and usage.

8.  Mark your calendar for a maintenance coat in 1-2 years.

After applying sealant

Sealing tile and grout will prolong the clean look and beauty of your tile installation. It provides a natural looking protective coating on interior and some exterior surfaces, and protects against water and oil-based stains.

Side Note

Enhance your next job with Red Devil’s Create-A-Color Caulk Kit

OLYMPUS DIGITAL CAMERAWith all of the beautiful tile and paint colors to choose from, why go with a bead of white caulk, when you can increase the wow factor with Red Devil’s Create-A-Color Caulk Kit? The kit has all you need to closely match just about any tile color. Using ordinary latex paint, chosen in the closest color to the tile or trimwork, just mix it in the special mixer and then apply with a caulk gun. The result is a tinted caulk that will dry to closely match the project color for a high end look!

The secret is a proprietary caulk blend that actually bonds to the paint rather than repelling it like standard caulks. Included in each kit is a Standard Caulk Mixer; two tubes of specially formulated Create-A-Color Caulk, a syringe for injecting the paint and an easy-to-follow instruction guide. The system works in minutes to create the perfect color and the mixer is very easy to clean and re-use for future projects. (Note: The mixer is not a caulk gun and is for mixing only).

Red Devil’s Create-A-Color Caulk is a quality formulation that has excellent adhesion, mildew resistance, interior and exterior performance, low odor and water clean-up.  Learn more at 1(800) 423-3845 or visit www.reddevil.com.

Hot Product

fence trac
FenceTrac Fence Systems

FenceTrac is a revolutionary fence system that uses patented U-channel rails and metal posts to create a secure and sturdy frame for any type of infill. You can choose from wood, vinyl, composite, bamboo, metal, or any other material that fits your style and budget. You can also mix and match different infills to create […]

Read More >>